October 29, 2026
How to make a tech pack in 9 steps
A tech pack is the document a factory builds from. Here is what goes in it, in the order to write it, and the mistakes that cost sample rounds.
The short answer
A tech pack is a technical document that tells a factory exactly how to make a garment or accessory: flats, bill of materials, measurements, grading, construction, colours and labelling. Make one by approving the design, drawing flats, listing materials, adding measurements and grading, and marking open questions before sending.
Key takeaways
- A tech pack is a brief the factory cannot misread: every guess you leave in it becomes a sample round.
- Always include flats, a BOM, measurements with tolerances, grading and construction notes.
- Mark open questions as open. A flagged gap is cheaper than a wrong assumption.
- Version every pack and name the approved design it was built from.
What goes into a tech pack, step by step?
1. Start from the approved design
Attach the final flat, colourway and any reference. The factory should build what the team signed off, so state the version and date.
2. Draw the technical flats
Show front, back and any side or detail view, with seams, stitching, pocket and trim positions. Keep one style per sheet.
3. List every material in the BOM
Name the shell, lining, interlining, trims, labels, zips and thread, with the supplier or spec, the colour and where each is used.
4. Write the measurements
Give the base size and the points of measure with tolerances. Say which size is the sample size.
5. Add the grading
Give the increment for each point of measure between sizes, so the factory can build the full size run.
6. Describe construction
Note stitch types, seam finishes, hems and any special technique, with a close-up where the flat is not enough.
7. Specify colours and prints
Give the colour references and the placement and scale of any print, graphic or embroidery.
8. Add labelling and packaging
Include the label positions, care and content information, hangtags, folding and packing instructions.
9. Review, version and send
Check every page against the approved design, mark open questions, version the file and send it with a clear request for the sample.
What does a complete tech pack contain?
| Section | What it holds | Typical mistake |
|---|---|---|
| Cover page | Style name and number, season, version, date, sample size | No version, so nobody knows which file is current |
| Technical flats | Front, back and detail views with seams and trims | Flats that do not match the approved render |
| Bill of materials | Shell, lining, trims, labels, thread, with supplier and colour | A trim missing, found at fit sample |
| Measurements | Points of measure, base size, tolerances | No tolerance, so every sample is argued over |
| Grading | Increments between sizes | Left out, so the factory guesses the size run |
| Construction | Stitching, seam finishes, special techniques | Assumed rather than written |
| Colour and print | Colour references, print placement and scale | A screen colour used as the reference |
| Labelling and packing | Labels, hangtags, folding and packing | Added late, after the bulk is cut |
Which mistakes cost the most?
- Details in email, not in the pack. Anything agreed in a thread but missing from the document will be missed.
- Old versions in circulation. Two people working from two files produce two different samples.
- Silence on the unknowns. If a measurement is undecided, say so, and name who decides.
- Flats that drift from the approved design. Re-check them every time the design changes.
How teams do this in CotonAI.
In CotonAI the tech pack sits on the same style record as the render and the colourways. It drafts from your technical drawings, specifications and BOM data, ties the pack to the approved version, and marks what is missing for sourcing to resolve. Available today: tech-pack drafts, BOMs and RFQ checklists. Fully editable tech packs and BOMs are coming next. See the AI tech pack generator.
Common questions
What is a tech pack?
A tech pack is the technical document a factory builds from. It holds flats, a bill of materials, measurements, grading, construction notes, colours and labelling for one style.
How long does it take to make a tech pack?
It depends on the product and on how much of the data already exists. A simple style with approved flats and a clear BOM goes much faster than a complex one with open decisions.
What is the difference between a tech pack and a spec sheet?
A spec sheet usually covers measurements only. A tech pack is the full package: flats, materials, measurements, grading, construction and labelling.
Can AI make a tech pack?
AI can draft one from technical drawings, specifications and BOM data and flag what is missing. A person still reviews it and fills the gaps. See our guide: Can AI make a tech pack?
Keep reading
Hand the factory a clean package. Every open question marked. We'll show you the workflow end to end and recommend where to start. Book a demo